9 Commands to Check CPU Information on Linux

By | August 13, 2020

CPU hardware information

The cpu information includes details about the processor, like the architecture, vendor name, model, number of cores, speed of each core etc.

There are quite a few commands on linux to get those details about the cpu.

In this post we shall take a look at some of the commonly used commands that can be used to get details about the cpu.

1. /proc/cpuinfo

The /proc/cpuinfo file contains details about individual cpu cores.
Output its contents with less or cat.

$ less /proc/cpuinfo
processor       : 0
vendor_id       : GenuineIntel
cpu family      : 6
model           : 23
model name      : Intel(R) Core(TM)2 Quad CPU    Q8400  @ 2.66GHz
stepping        : 10
microcode       : 0xa07
cpu MHz         : 1998.000
cache size      : 2048 KB
physical id     : 0
siblings        : 4
core id         : 0
cpu cores       : 4
apicid          : 0
initial apicid  : 0
fpu             : yes
fpu_exception   : yes
cpuid level     : 13
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 xsave lahf_lm dtherm tpr_shadow vnmi flexpriority
bogomips        : 5303.14
clflush size    : 64
cache_alignment : 64
address sizes   : 36 bits physical, 48 bits virtual
power management:

Every processor or core is listed separately the various details about speed, cache size and model name are included in the description.

To count the number of processing units use grep with wc

$ cat /proc/cpuinfo | grep processor | wc -l
4
The number of processors shown by /proc/cpuinfo might not be the actual number of cores on the processor. For example a processor with 2 cores and hyperthreading would be reported as a processor with 4 cores.

To get the actual number of cores, check the core id for unique values

$ cat /proc/cpuinfo | grep 'core id'
core id         : 0
core id         : 2
core id         : 1
core id         : 3

So there are 4 different core ids. This indicates that there are 4 actual cores.

2. lscpu - display information about the CPU architecture

lscpu is a small and quick command that does not need any options. It would simply print the cpu hardware details in a user-friendly format.

$ lscpu
Architecture:          x86_64
CPU op-mode(s):        32-bit, 64-bit
Byte Order:            Little Endian
CPU(s):                4
On-line CPU(s) list:   0-3
Thread(s) per core:    1
Core(s) per socket:    4
Socket(s):             1
NUMA node(s):          1
Vendor ID:             GenuineIntel
CPU family:            6
Model:                 23
Stepping:              10
CPU MHz:               1998.000
BogoMIPS:              5303.14
Virtualization:        VT-x
L1d cache:             32K
L1i cache:             32K
L2 cache:              2048K
NUMA node0 CPU(s):     0-3

3. hardinfo

Hardinfo is a gtk based gui tool that generates reports about various hardware components. But it can also run from the command line only if there is no gui display available.

$ hardinfo | less

It would produce a large report about many hardware parts, by reading files from the /proc directory. The cpu information is towards the beginning of the report. The report can also be written to a text file.

Hardinfo also performs a few benchmark tests taking a few minutes before the report is displayed.

4. lshw

The lshw command can display limited information about the cpu. lshw by default shows information about various hardware parts, and the '-class' option can be used to pickup information about a specific hardware part.

$ sudo lshw -class processor
  *-cpu                   
       description: CPU
       product: Intel(R) Core(TM)2 Quad CPU    Q8400  @ 2.66GHz
       vendor: Intel Corp.
       physical id: 0
       bus info: cpu@0
       version: Intel(R) Core(TM)2 Quad CPU    Q8400  @ 2.66GHz
       slot: LGA 775
       size: 1998MHz
       capacity: 4GHz
       width: 64 bits
       clock: 333MHz
       capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx x86-64 constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 xsave lahf_lm dtherm tpr_shadow vnmi flexpriority cpufreq

The vendor, model and speed of the processor are being shown correctly. However it is not possible to deduce the number of cores on the processor from the above output.

To learn more about the lshw command check this post:
lshw command examples to get hardware information on Linux

5. nproc

The nproc command just prints out the number of processing units available. Note that the number of processing units might not always be the same as number of cores.

$ nproc
4

6. dmidecode

The dmidecode command displays some information about the cpu, which includes the socket type, vendor name and various flags.

$ sudo dmidecode -t 4
# dmidecode 2.12
SMBIOS 2.4 present.

Handle 0x0000, DMI type 4, 35 bytes
Processor Information
        Socket Designation: LGA 775
        Type: Central Processor
        Family: Pentium D
        Manufacturer: Intel(R) Corporation
        ID: 7A 06 01 00 FF FB EB BF
        Signature: Type 0, Family 6, Model 23, Stepping 10
        Flags:
                FPU (Floating-point unit on-chip)
                VME (Virtual mode extension)
                DE (Debugging extension)
                PSE (Page size extension)
                TSC (Time stamp counter)
                MSR (Model specific registers)
                PAE (Physical address extension)
                MCE (Machine check exception)
                CX8 (CMPXCHG8 instruction supported)
                APIC (On-chip APIC hardware supported)
                SEP (Fast system call)
                MTRR (Memory type range registers)
                PGE (Page global enable)
                MCA (Machine check architecture)
                CMOV (Conditional move instruction supported)
                PAT (Page attribute table)
                PSE-36 (36-bit page size extension)
                CLFSH (CLFLUSH instruction supported)
                DS (Debug store)
                ACPI (ACPI supported)
                MMX (MMX technology supported)
                FXSR (FXSAVE and FXSTOR instructions supported)
                SSE (Streaming SIMD extensions)
                SSE2 (Streaming SIMD extensions 2)
                SS (Self-snoop)
                HTT (Multi-threading)
                TM (Thermal monitor supported)
                PBE (Pending break enabled)
        Version: Intel(R) Core(TM)2 Quad CPU    Q8400  @ 2.66GHz
        Voltage: 1.6 V
        External Clock: 333 MHz
        Max Speed: 4000 MHz
        Current Speed: 2666 MHz
        Status: Populated, Enabled
        Upgrade: Socket LGA775
        L1 Cache Handle: 0x0003
        L2 Cache Handle: 0x0001
        L3 Cache Handle: Not Provided
        Serial Number: Not Specified
        Asset Tag: Not Specified
        Part Number: Not Specified

7. cpuid

The cpuid command fetches CPUID information about Intel and AMD x86 processors.

The program can be installed with apt on ubuntu

$ sudo apt-get install cpuid

And here is sample output

$ cpuid

.....

Vendor ID: "GenuineIntel"; CPUID level 13

Intel-specific functions:
Version 0001067a:
Type 0 - Original OEM
Family 6 - Pentium Pro
Model 7 - Pentium III/Pentium III Xeon - external L2 cache
Stepping 10
Reserved 4

Extended brand string: "Intel(R) Core(TM)2 Quad CPU    Q8400  @ 2.66GHz"
CLFLUSH instruction cache line size: 8
Initial APIC ID: 2
Hyper threading siblings: 4

Feature flags bfebfbff:
FPU    Floating Point Unit
VME    Virtual 8086 Mode Enhancements
DE     Debugging Extensions
PSE    Page Size Extensions
TSC    Time Stamp Counter
MSR    Model Specific Registers
PAE    Physical Address Extension
MCE    Machine Check Exception
CX8    COMPXCHG8B Instruction
APIC   On-chip Advanced Programmable Interrupt Controller present and enabled
SEP    Fast System Call
MTRR   Memory Type Range Registers
PGE    PTE Global Flag
MCA    Machine Check Architecture
CMOV   Conditional Move and Compare Instructions
FGPAT  Page Attribute Table
PSE-36 36-bit Page Size Extension
CLFSH  CFLUSH instruction
DS     Debug store
ACPI   Thermal Monitor and Clock Ctrl
MMX    MMX instruction set
FXSR   Fast FP/MMX Streaming SIMD Extensions save/restore
SSE    Streaming SIMD Extensions instruction set
SSE2   SSE2 extensions
SS     Self Snoop
HT     Hyper Threading
TM     Thermal monitor
31     reserved

.....

8. inxi

Inxi is a script that uses other programs to generate a well structured easy to read report about various hardware components on the system. Check out the full tutorial on inxi.

$ sudo apt-get install inxi

Print out cpu/processor related information

$ inxi -C
CPU:       Quad core Intel Core2 Quad CPU Q8400 (-MCP-) cache: 2048 KB flags: (lm nx sse sse2 sse3 sse4_1 ssse3 vmx) 
           Clock Speeds: 1: 1998.00 MHz 2: 1998.00 MHz 3: 1998.00 MHz 4: 1998.00 MHz

To learn more about the inxi command and its usage check out this post:
How to use "Inxi" to check Hardware Information on Linux

9. Hwinfo

The hwinfo command is a hardware information program that can be used to collect details about various hardware components on a Linux system.

It also displays information about the processor. Here is a quick example:

$ hwinfo --short --cpu
cpu:                                                            
                       Intel(R) Core(TM) i5-7400 CPU @ 3.00GHz, 2275 MHz
                       Intel(R) Core(TM) i5-7400 CPU @ 3.00GHz, 2262 MHz
                       Intel(R) Core(TM) i5-7400 CPU @ 3.00GHz, 2058 MHz
                       Intel(R) Core(TM) i5-7400 CPU @ 3.00GHz, 2133 MHz
$

If you don't use the "--short" option it will display much more information about each cpu core like architecture and processor features.

To learn more about the hwinfo command check this post:
Check hardware information on Linux with "hwinfo" command

Conclusion

Those were some of the commands to check CPU information on Linux based systems like Ubuntu, Fedora, Debian, CentOS etc.

For some more command examples on checking cpu information check this post:
How to Check Processor and CPU Details on Linux - Command Examples

Most of the commands are command line based and show text output. For a GUI interface use the program called Hardinfo.

It shows hardware details about various components in a easy to use GUI interface.

If you know of any other useful command that can display information about the CPU, let us know in the comments below.

About Silver Moon

A Tech Enthusiast, Blogger, Linux Fan and a Software Developer. Writes about Computer hardware, Linux and Open Source software and coding in Python, Php and Javascript. He can be reached at [email protected].

15 Comments

9 Commands to Check CPU Information on Linux
  1. SkipDaShu

    lshw now (DISTRIB_DESCRIPTION=”Linux Mint 17.3 Rosa”) includes a line like below at the bottom of it’s listing:

    configuration: cores=4 enabledcores=4 threads=8

  2. Guille

    How to get the number of real cores, not HiperThreading.

    For example, for i7, real cores are 4, but logical are 8. There is some way without root ?

  3. ViruSzZ

    yo Silver Moon, nice write-up bro. absolutelly useful stuff there, though the number of CPUs can be fetched using just ‘grep -c processor /proc/cpuinfo’. take care :)

  4. nothanks

    Thank you for the helpful information. You can not look for “unique values” with the “cat /proc/cpuinfo |grep ‘core id'” command on a multiprocessor system. The situation gets even worse with hyperthreading enabled CPU’s.

Leave a Reply

Your email address will not be published. Required fields are marked *